Restoring your hail damaged vehicle complete guides? The first step to performing a dent repair without using paint involves assessing the dent itself and determining if a paintless dent repair is even possible. According to most experts, 80 to 90 percent of dents can be repaired using PDR techniques. However, there are a certain percentage of dents that are impossible to repair without following it up with a paint job. The following types of dents usually fall into this “non-PDR” category: Very deep dents – Even very large dents can be repaired using PDR if the dent is fairly shallow. However, if a dent of any size is pushed in too far, the metal can’t be bent back into place without damaging the paint and requiring repainting.

1st let’s start with some car paint care tricks: Clean the Car. One of the most important things you can do to maintain the exteriors of your car is to wash and shampoo the vehicle regularly. Commercial power washes are also beneficial if you use them every few months. Make sure you keep a good distance between the surface of the car and the pressure jet, so you don’t damage the paint. If you’re unsure you could get it done professionally.

So, we’ve explained what the procedure looks like — assuming it was done properly. And as you could probably guess there are a lot of ways an amateur or first-timer can get it wrong. It’s different than most other car repairs because it’s not about mechanical prowess; it’s more about control and the ability to maintain a steady hand and a gentle pace. You can’t rush it. The problem is, once a sheet metal repair starts to go awry, you’re usually much, much worse off than if you’d just left it alone. Metal holds its shape, but only to a certain point. Let’s say you get a dent in the hood — nothing too drastic, just a shallow, even dent with no sharp creases in an area that’s pretty easy to reach. You think it’ll be easy to pop it out on your own, so you begin to massage the underside while holding your shaping tool in place. You’ve made good progress so far, and a casual observer wouldn’t even notice the flawed area. But it’s not exactly perfect, and since it’s been fairly easy to this point, you decide to keep massaging the area to make it flawless. After a few more minutes of massaging, you realize that you’ve pushed it just a little too far. And now you’ve got this flabby area on the hood where you stretched out the metal. And there’s no easy way to shrink it back down. Keep going and it’ll stretch even more. Lesson learned.

This technique is popular among automotive enthusiasts when it comes to the removal of small dents. The idea is simple: heat will inevitably cause the metal surface to expand and (hopefully) pop the dent out. Remember that the more time the car spends time under the sun, the better this technique will work. Use a plastic and/or leather conditioner for the car’s interior, so as to not damage it while exposing the car to maximum sunlight. If the sun’s heat isn’t particularly strong that day, a simple hair dryer could be used in conjunction with the sun to concentrate the heat to a specific area. Point the hair dryer to the dented area for two-minute intervals until the dent pops out. Be careful not to touch the hot lip of the hair dryer on any painted surface. A two-to-four inch gap between the dryer and the surface is recommended.

Repair times are up to the severity of the hailstorm and the damage on your car. For the light or moderate damages, the repairs may take from 1 to 3 days. But for heavy damages, it may take you 2 to 3 weeks as that damages will needs body shop participation, for paint work and panel replacement.

Decontamination: Life is a jungle out there and the air is filled with unseen pollutants. Never mind the fact that you are breathing these pollutants into your lungs, but the endless particles of pollution is in fact harmful to your car paint. Nest time you have your car washed, glide your hand across the surface of your new car paint ans see if you don’t feel a surface that is less than silky smooth. Most likely you your hand will feel what feels like small particles stuck to the paint that will give it a certain unwanted texture.

We recommend going to a professional repair service to avoid a lot of extra costs. Meet EvidentPDR in Colorado. Leo has over 15 years of experience with print services, vinyl wrap, window tinting, graphic design, and physical advertising. After many years of working with Pinnacle Signs, he then founded LD Wraps for 5 years, where he acquired many large accounts in Colorado Springs, everything from designing for local breweries, news stations, and real estate. Ben and Leo met through several business interactions, where Ben asked Leo to design several vinyl decals, stickers, signs, and banners you see in our shop. Discover extra details on https://www.evidentpdr.com/.

Use Hot Glue, Wooden Dowels, & Screws: When you attempt to take out dents yourself, you always put the risk that you might further damage your car, whether you make the dent worse or chip the paint. A safe way of trying to take out big dents on your car is by using several wooden dowels, a few screws, and a hot glue gun. Simply place two nails into each side of the dowel and put the hot glue on the bottom. Place the dowels glue-side down in areas around the dent, repeat as many times as needed to cover the area, let them dry, and pull each one out until the dent is gone.